Best Car Amplifiers. Reviews September, 2020

BOSS Audio Systems R1100M Monoblock Car Amplifier - 1100 Watt Amp, 2/4 Ohm Stable, Class A/B, Mosfet Power Supply, Remote Subwoofer Control, Subwoofer Amplifier

Search only BOSS Audio Systems brand name
BOSS Audio Systems R1100M Monoblock Car Amplifier - 1100 Watt Amp, 2/4 Ohm Stable, Class A/B, Mosfet Power Supply, Remote Subwoofer Control, Subwoofer Amplifier

Current price: 66.14 USD


Check price and availability


Height: 2.25 Inches

Length: 9.13 Inches

Width: 10.44 Inches

Weight: 4.4 Pounds

Warranty: 6 Year Platinum Online Dealer Warranty valid only on products Sold / Shipped by Amazon.com. This offer is not valid on purchases made from third party market place sellers

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety

More Info

Crunch PX1000.4 Power Amplifier (Class Ab, 4 Channels, 1,000 Watts), 3.70in. x 12.60in. x 10.80in.

Search only Crunch brand name
Crunch PX1000.4 Power Amplifier (Class Ab, 4 Channels, 1,000 Watts), 3.70in. x 12.60in. x 10.80in.

Current price: 61.13 USD

Saving: $8.86 (13%)


Check price and availability


Height: 3 Inches

Length: 4 Inches

Width: 5 Inches

Weight: 1 Pounds

Warranty: Please contact the manufacturer

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs

More Info

BOSS Audio Systems R1100MK Car Amplifier and 8 Gauge Wiring Kit - 1100 Watts Max Power, 2-4 Ohm Stable, Class A/B, Monoblock, Mosfet Power Supply, Remote Subwoofer Control

Search only BOSS Audio Systems brand name
BOSS Audio Systems R1100MK Car Amplifier and 8 Gauge Wiring Kit - 1100 Watts Max Power, 2-4 Ohm Stable, Class A/B, Monoblock, Mosfet Power Supply, Remote Subwoofer Control

Current price: 89.99 USD


Check price and availability


Height: 2.3 Inches

Length: 9.1 Inches

Width: 10.4 Inches

Weight: 4.4 Pounds

Warranty: 6 Year Platinum Online Dealer Warranty valid only on products Sold / Shipped by Amazon.com. This offer is not valid on purchases made from third party market place sellers

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse

More Info

Blaupunkt 1600W 4-Channel, Full-Range Amplifier AMP1604

Search only BLAUPUNKT brand name
Blaupunkt 1600W 4-Channel, Full-Range Amplifier AMP1604

Current price: 62.76 USD

Saving: $10.24 (14%)


Check price and availability


Height: 2.2 Inches

Length: 11 Inches

Width: 7.4 Inches

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W

More Info

Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier Car Audio Amp

Search only Rockville brand name
Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier Car Audio Amp

Current price: 129.95 USD


Check price and availability


Height: 3 Inches

Length: 3 Inches

Width: 3 Inches

Weight: 8 Pounds

Warranty: 1 YEAR

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel

More Info

Planet Audio AC1800.5 5 Channel Car Amplifier - 1800 Watts, Full Range, Class A/B, 2-4 Ohm Stable, Mosfet Power Supply, Bridgeable

Search only Planet Audio brand name
Planet Audio AC1800.5 5 Channel Car Amplifier - 1800 Watts, Full Range, Class A/B, 2-4 Ohm Stable, Mosfet Power Supply, Bridgeable

Current price: 134.99 USD


Check price and availability


Height: 2.4 Inches

Length: 19.7 Inches

Width: 10 Inches

Weight: 14 Pounds

Warranty: 6 Year Platinum Online Dealer Warranty

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel
  • Warranty - Planet Audio provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions - Depth 19.7” x Width 10” x Height 2.4”, Weight – 14 lbs.
  • Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels
  • Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Power - 300 watts max x 4 @2-Ohms plus 5th channel 600 watts max x 1 @2-Ohms, 150 watts max x 4 @4-Ohms plus 5th channel 300 watts max x 1 @-4-Ohms, 600 watts max x 2 bridged @4 Ohms

More Info

Blaupunkt 1500W 4-Channel, Full-Range Amplifier

Search only BLAUPUNKT brand name
Blaupunkt 1500W 4-Channel, Full-Range Amplifier

Current price: 74.95 USD


Check price and availability


Height: 7.02 Inches

Length: 4.09 Inches

Width: 1.36 Inches

Weight: 0.03 Pounds

Warranty: 1 year

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel
  • Warranty - Planet Audio provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions - Depth 19.7” x Width 10” x Height 2.4”, Weight – 14 lbs.
  • Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels
  • Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Power - 300 watts max x 4 @2-Ohms plus 5th channel 600 watts max x 1 @2-Ohms, 150 watts max x 4 @4-Ohms plus 5th channel 300 watts max x 1 @-4-Ohms, 600 watts max x 2 bridged @4 Ohms
  • This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system
  • Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road
  • 1500W Maximum Power Full-Range Amplifier

More Info

Pioneer GM-A6704 4-Channel Bridgeable Amplifier with Bass Boost,Black/red

Search only PIONEER brand name
Pioneer GM-A6704 4-Channel Bridgeable Amplifier with Bass Boost,Black/red

Current price: 163.99 USD

Saving: $36.01 (18%)


Check price and availability


Height: 2.4 Inches

Length: 14.1 Inches

Width: 8.5 Inches

Weight: 4.9 Pounds

Warranty: 1 year

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel
  • Warranty - Planet Audio provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions - Depth 19.7” x Width 10” x Height 2.4”, Weight – 14 lbs.
  • Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels
  • Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Power - 300 watts max x 4 @2-Ohms plus 5th channel 600 watts max x 1 @2-Ohms, 150 watts max x 4 @4-Ohms plus 5th channel 300 watts max x 1 @-4-Ohms, 600 watts max x 2 bridged @4 Ohms
  • This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system
  • Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road
  • 1500W Maximum Power Full-Range Amplifier
  • Adjustable bass boost
  • Variable high pass filter
  • Automatic signal sensing and Turn-On
  • 1000 Watts Max Power

More Info

Rockville RVA-M2 2500w Peak/625w CEA RMS @ 1 Ohm Amplifier Mono Car Amp+Remote

Search only Rockville brand name
Rockville RVA-M2 2500w Peak/625w CEA RMS @ 1 Ohm Amplifier Mono Car Amp+Remote

Current price: 112.1 USD


Check price and availability


Warranty: 1 YEAR

  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel
  • Warranty - Planet Audio provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions - Depth 19.7” x Width 10” x Height 2.4”, Weight – 14 lbs.
  • Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels
  • Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Power - 300 watts max x 4 @2-Ohms plus 5th channel 600 watts max x 1 @2-Ohms, 150 watts max x 4 @4-Ohms plus 5th channel 300 watts max x 1 @-4-Ohms, 600 watts max x 2 bridged @4 Ohms
  • This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system
  • Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road
  • 1500W Maximum Power Full-Range Amplifier
  • Adjustable bass boost
  • Variable high pass filter
  • Automatic signal sensing and Turn-On
  • 1000 Watts Max Power
  • Damping Factor: >150 @ 100Hz, Fuse: 30A*2, Technology: This series uses a reliable Class D circuitry that gives you the most reliability and the most power for your money, Dimensions: (L x W x H) 13" x 8.5" x 2.24", Weight: 7 lbs
  • S/N Ratio: >90dB, Under Voltage Protection at 9V, Over Voltage Protection at 16V, Radiation cooling keeps the amp running at high volumes for hours straight, Extruded aluminum heatsink, Frequency Response: 10Hz - 300Hz
  • Phase Control Switch, Full IC-Controlled Protection Circuitry, Adjustable 0-12dB Bass Equalizer, Mute and Delay Soft Start System, Status Mode LED Indicator, Minimum THD at Rated Power:

More Info

Rockville RXA-F1 1600 Watt Peak/800w RMS 4 Channel Car Stereo Amplifier+Amp Kit

Search only Rockville brand name
Rockville RXA-F1 1600 Watt Peak/800w RMS 4 Channel Car Stereo Amplifier+Amp Kit

Current price: 124.95 USD


Check price and availability


  • Warranty - BOSS Audio Systems provides a powerful 3-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 0.4” x 2.3”, It can be installed in a variety of different places due to its’ slim and compact design, Weight: 4.43 Lbs. Amplifier Car Audio. Monoblock amplifier
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Power - Maximum Power Output of 1100 Watts at 2 Ohms into one channel. Max power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • Installation - Connect Power/ground to the closest point of chassis of the vehicle. Keep ground wire less than 39” (100 cm) in length. Use 8 gauge or heavier wire. A Mobile Electronics Certified Professional is recommended for installation & safety
  • (Quick Thermal Dispersion) technology heat sink Low-noise preamp
  • Low-level RCA inputs & outputs
  • High-level inputs
  • Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.
  • Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms
  • Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect
  • Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse
  • Signal-To- Noise Ratio: =>96dB
  • Crossover Frequency: 50Hz - 250Hz - Crossover Slope (dB/oct): 8-10dB/oct
  • Frequency Response: 10Hz - 30Hz
  • RMS Power (4 Ohms): 55W x 4 - RMS Power (2 Ohms): 79W x 4
  • Blaupunkt AMP1604 4-Channel, Full-Range Amplifier Max. Output Power: 1600W
  • Minimum THD at Rated Power: 90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz - 250Hz. Damping Factor: >150 @ 100Hz. 80 Amp Maxi Fuse. Dimensions: (W x H x L) 9˝ x 2.4˝ x 14.7˝.
  • High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator.
  • RMS Power Ratings: (Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc.). 2 Ohm: 1500 Watts x 1 Channel. 4 Ohm: 900 Watts x 1 Channel. Peak: (The amount of power the amplifier can produce for a split second at the loudest part of a song. 2 Ohm: 3000 Watts x 1 Channel. 4 Ohm: 1800 Watts x 1 Channel.
  • Rockville dB13 3000 Watt/1500w RMS Mono Class D 2 Ohm Amplifier. CEA Compliant Power Ratings (Rated at less than 1 % distortion) (Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc.). 2 Ohm: 750 Watts x 1 Channel
  • Warranty - Planet Audio provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality
  • Specs - Dimensions - Depth 19.7” x Width 10” x Height 2.4”, Weight – 14 lbs.
  • Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels
  • Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
  • Power - 300 watts max x 4 @2-Ohms plus 5th channel 600 watts max x 1 @2-Ohms, 150 watts max x 4 @4-Ohms plus 5th channel 300 watts max x 1 @-4-Ohms, 600 watts max x 2 bridged @4 Ohms
  • This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system
  • Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road
  • 1500W Maximum Power Full-Range Amplifier
  • Adjustable bass boost
  • Variable high pass filter
  • Automatic signal sensing and Turn-On
  • 1000 Watts Max Power
  • Damping Factor: >150 @ 100Hz, Fuse: 30A*2, Technology: This series uses a reliable Class D circuitry that gives you the most reliability and the most power for your money, Dimensions: (L x W x H) 13" x 8.5" x 2.24", Weight: 7 lbs
  • S/N Ratio: >90dB, Under Voltage Protection at 9V, Over Voltage Protection at 16V, Radiation cooling keeps the amp running at high volumes for hours straight, Extruded aluminum heatsink, Frequency Response: 10Hz - 300Hz
  • Phase Control Switch, Full IC-Controlled Protection Circuitry, Adjustable 0-12dB Bass Equalizer, Mute and Delay Soft Start System, Status Mode LED Indicator, Minimum THD at Rated Power:
  • This unit also features a high speed MOSFET power supply, studio-grade bipolar output stage transistors and ELNA brand audiophile capacitors. It has a fully adjustable 12dB/Octave cross over with differential circuitry. High Level inputs, also referred to as Speaker Level inputs, allow you to install the amplifier into your vehicle even if you do not have any preamp outputs available.
  • Accessories Included: Wire Ties, Ring Terminals, Butt Connectors, Spades, and Grommets. Soft abrasion proof insulating jacket allows for 100% improved flexibility. PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F
  • 4 Gauge 4 Channel Car Amplifier Wiring Installation Kit. (2) 17 High Grade Twisted Pair of 100% Copper RCA Cable. 17 4 Gauge Translucent Blue SuperFlex Power Cables. 17 18 Gauge Blue Remote Cable. 17 16 Gauge Clear Speaker Wire. 3 4 Gauge Clear SuperFlex Ground Wire. Gold Plated AGU Heat Resistant Fuse Holder. 60 Amp AGU Gold Plated Fuse. 7 Split Tube Loom
  • Mute and Delay Soft Start System. Full IC-Controlled Protection Circuitry. 2 CH / 4 CH Input Mode Switch. RCA Preamp Line Output. ELNA Brand Audiophile Capacitors. 8 Volt Preamp Circuitry. Status Mode LED Indicator. Minimum THD: 200 @ 100Hz. 60 Amp Maxi Fuse
  • 1600 Watt Peak/800w RMS 4 Channel Amplifier Car Stereo Amp. Peak Power: 1600 Watts (2 x 800 @ 2 ohms or 1 x 1600 @ 4 Ohms). High-Speed MOSFET Power Supply. Studio-Grade Bipolar Output Stage Transistors. Fully Adjustable 12dB Bass Equalizer. 2-Ohm Stable Stereo. 4-Ohm Mono Bridgeable. 3 Channel Mixed-Mono Capable

More Info

1    2    3    4    5    6    7    8    9    10