Best Water Pipe Heat Cables. HEATIT brand. New releases 2020

HEATIT HISD 6-feet Pipe Heating Cable with with Built-in Thermostat, Black

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT HISD 6-feet Pipe Heating Cable with with Built-in Thermostat, Black

Current price: 17.99 USD

Saving: $18.01 (50%)


Check price and availability


Height: 28 Inches

Length: 5 Inches

Width: 19 Inches

Weight: 0.37 Pounds

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.

More Info

HEATIT Mobile Home 100-feet HEATIT HTM Braid Self Regulating heating cable Water Line Freeze Protection

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT Mobile Home 100-feet HEATIT HTM Braid Self Regulating heating cable Water Line Freeze Protection

Current price: 111.99 USD


Check price and availability


Weight: 2.6 Pounds

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.

More Info

HEATIT JHSF 24-feet 120V Regulating Pre-assembled Pipe Cable

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT JHSF 24-feet 120V Regulating Pre-assembled Pipe Cable

Current price: 30.99 USD


Check price and availability


Height: 3 Inches

Length: 21 Inches

Width: 4 Inches

Weight: 1.11 Pounds

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).

More Info

HEATIT JHSF1-CT Self Reguting Pre-asembled Pipe Heting Cable 12-feet 220V

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT JHSF1-CT Self Reguting Pre-asembled Pipe Heting Cable 12-feet 220V

Current price: 33.99 USD


Check price and availability


Height: 2 Inches

Length: 45 Inches

Width: 1 Inches

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.

More Info

HEATIT JHSF 30-feet 220V Self Reglating Pre-asembled Pipe Heting Cable (Renewed)

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT JHSF 30-feet 220V Self Reglating Pre-asembled Pipe Heting Cable (Renewed)

Current price: 28.38 USD


Check price and availability


Height: 4 Inches

Length: 22 Inches

Width: 4 Inches

Warranty: 90 days limited warranty

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • Testing the cable before the instalation. Uncoil the cable, plug in the heating cable and then put the themotat part of the cable into an ice bucket for few minutes. When the tempeture is below 37F, the thermtat will engize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Indtrial grade heat shrinkage tube for conection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asembled, easy to install. Including grounded plug with light, built in theostat(turn the cable 37F on 50F off), and instrctions. 120 volt, 3 watts/ft at 50 degrees F. Energy-eficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on platic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost prottion etc). Self regulang heting cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambient tempture is below 37F/3 degree C. Please test the cable in a cold envirent. HEATIT is regiered Tradmark by zhukeshi(We didn't authize other sellers in Amazon.com).

More Info

HEATIT ET-21 Freeze Thermostatically Controlled outlet On at 38F /Off at 50F

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT ET-21 Freeze Thermostatically Controlled outlet On at 38F /Off at 50F

Current price: 10.99 USD

Saving: $10.00 (48%)


Check price and availability


  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • Testing the cable before the instalation. Uncoil the cable, plug in the heating cable and then put the themotat part of the cable into an ice bucket for few minutes. When the tempeture is below 37F, the thermtat will engize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Indtrial grade heat shrinkage tube for conection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asembled, easy to install. Including grounded plug with light, built in theostat(turn the cable 37F on 50F off), and instrctions. 120 volt, 3 watts/ft at 50 degrees F. Energy-eficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on platic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost prottion etc). Self regulang heting cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambient tempture is below 37F/3 degree C. Please test the cable in a cold envirent. HEATIT is regiered Tradmark by zhukeshi(We didn't authize other sellers in Amazon.com).
  • Make a test when you received the product.  Put it into the freezer for 45 minutes.  And then plug in and you will see the red light on the thermostat control. Two year limited warranty- If you are not completely satisfied with HEATIT ET-21, please don't hesitate to contact us in any time, we'll try our best to solve your issues.
  • Can be use for other applications: 120 VAC electric heaters, gas heater, Engine heaters, pipe heat tape, roof heating cable and so on
  • Easy installation: just plug this device into electrical outlet. Maximum 15 amps. CSA approved. Only for dry location.
  • Energize below 38℉(3℃) and to turn off automatically at approximately 50℉(10℃). Automatically turns power on and off according to ambient temperature. Save energy and save money
  • Thermostat control outlet with the smart indicator light: The indicator light turns on when it's below 38 and it has energized the outlet.

More Info

HEATIT HIRD 60 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT HIRD 60 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

Current price: 43.99 USD

Saving: $12.00 (21%)


Check price and availability


  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • Testing the cable before the instalation. Uncoil the cable, plug in the heating cable and then put the themotat part of the cable into an ice bucket for few minutes. When the tempeture is below 37F, the thermtat will engize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Indtrial grade heat shrinkage tube for conection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asembled, easy to install. Including grounded plug with light, built in theostat(turn the cable 37F on 50F off), and instrctions. 120 volt, 3 watts/ft at 50 degrees F. Energy-eficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on platic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost prottion etc). Self regulang heting cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambient tempture is below 37F/3 degree C. Please test the cable in a cold envirent. HEATIT is regiered Tradmark by zhukeshi(We didn't authize other sellers in Amazon.com).
  • Make a test when you received the product.  Put it into the freezer for 45 minutes.  And then plug in and you will see the red light on the thermostat control. Two year limited warranty- If you are not completely satisfied with HEATIT ET-21, please don't hesitate to contact us in any time, we'll try our best to solve your issues.
  • Can be use for other applications: 120 VAC electric heaters, gas heater, Engine heaters, pipe heat tape, roof heating cable and so on
  • Easy installation: just plug this device into electrical outlet. Maximum 15 amps. CSA approved. Only for dry location.
  • Energize below 38℉(3℃) and to turn off automatically at approximately 50℉(10℃). Automatically turns power on and off according to ambient temperature. Save energy and save money
  • Thermostat control outlet with the smart indicator light: The indicator light turns on when it's below 38 and it has energized the outlet.
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable.
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available; Suitable for most roof and gutter configurations.
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts.
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included.
  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact us in any time.

More Info

HEATIT Aluminum Foil Tape Professional Grade 2 inch x 30 feet (10yard Length) Thick 5.3mil (2.4mil foil and 2.9mil Backing Paper) for HVAC, Ducts, Pipes, Metal Repair, Heating Cable Application etc

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT Aluminum Foil Tape Professional Grade 2 inch x 30 feet (10yard Length) Thick 5.3mil (2.4mil foil and 2.9mil Backing Paper) for HVAC, Ducts, Pipes, Metal Repair, Heating Cable Application etc

Current price: 7.99 USD

Saving: $3.00 (27%)


Check price and availability


  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • Testing the cable before the instalation. Uncoil the cable, plug in the heating cable and then put the themotat part of the cable into an ice bucket for few minutes. When the tempeture is below 37F, the thermtat will engize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Indtrial grade heat shrinkage tube for conection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asembled, easy to install. Including grounded plug with light, built in theostat(turn the cable 37F on 50F off), and instrctions. 120 volt, 3 watts/ft at 50 degrees F. Energy-eficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on platic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost prottion etc). Self regulang heting cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambient tempture is below 37F/3 degree C. Please test the cable in a cold envirent. HEATIT is regiered Tradmark by zhukeshi(We didn't authize other sellers in Amazon.com).
  • Make a test when you received the product.  Put it into the freezer for 45 minutes.  And then plug in and you will see the red light on the thermostat control. Two year limited warranty- If you are not completely satisfied with HEATIT ET-21, please don't hesitate to contact us in any time, we'll try our best to solve your issues.
  • Can be use for other applications: 120 VAC electric heaters, gas heater, Engine heaters, pipe heat tape, roof heating cable and so on
  • Easy installation: just plug this device into electrical outlet. Maximum 15 amps. CSA approved. Only for dry location.
  • Energize below 38℉(3℃) and to turn off automatically at approximately 50℉(10℃). Automatically turns power on and off according to ambient temperature. Save energy and save money
  • Thermostat control outlet with the smart indicator light: The indicator light turns on when it's below 38 and it has energized the outlet.
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable.
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available; Suitable for most roof and gutter configurations.
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts.
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included.
  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact us in any time.
  • Idea for Indoor and outdoor applications: pipe heating cable attachment, duct insulation, general repair, cold and hot air ducts, HVAC, aluminum sealing, copper pipe fixing etc
  • Flame retardant, UV resistant, Chemically resistant. Perform well in thermally conductive. Improving the heating and cooling efficiency
  • HEATIT aluminum foil tape can stick well to most surfaces by its high quality acrylic pressure sensitive adhesive. A clean, dry and free of oil or grease surface is necessary before applying HEATIT aluminum foil tape
  • 2.0 inches wide x 30 feet (10 yards) length. 2.4 mil foil thick and 2.9 mil backing paper thick
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HEATIT aluminum foil tape provide a tough, strong bond at low and high temperatures from -22 F to 248 F

More Info

HEATIT JHSF1 Self Regulating ROOF & Gutter DE-Icing Pre-Assembled Heating Cable 125-feet 120V

More from Tools & Home Improvement
Search only HEATIT brand name
HEATIT JHSF1 Self Regulating ROOF & Gutter DE-Icing Pre-Assembled Heating Cable 125-feet 120V

Current price: 116.99 USD


Check price and availability


Weight: 2.6 Pounds

  • Copper
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow.
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
  • Testing the cable before the instaation. Uncoil the cable, plug in the heating cable and then put the therstat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrkage tube for conction.The lowest insllation temature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asmbled, easy to install. Including grounded plug with light, built in thermtat(turn the cable 37F on 50F off), and instrtions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulang heting cable output will adjust autotically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambent tempeture is below 37F/3 degree C. Please test the cable in a cold envinment. HEATIT is registed Traemark by zhushi(We didn't authorize other sellers in Amazon.com).
  • Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we'll try our best to solve your issue.
  • Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Protect pipes up to 2 1/2" in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
  • Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
  • HEATIT is regisred Tradeark by zhukhi(We didn't ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • Testing the cable before the instalation. Uncoil the cable, plug in the heating cable and then put the themotat part of the cable into an ice bucket for few minutes. When the tempeture is below 37F, the thermtat will engize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue
  • ETL approved. 2 ft 18/3 cold lead with plug. Indtrial grade heat shrinkage tube for conection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
  • Pre-asembled, easy to install. Including grounded plug with light, built in theostat(turn the cable 37F on 50F off), and instrctions. 120 volt, 3 watts/ft at 50 degrees F. Energy-eficient. Protect pipes up to 2" in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
  • Suitable for use on platic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost prottion etc). Self regulang heting cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
  • JHSF doesn't work unless the ambient tempture is below 37F/3 degree C. Please test the cable in a cold envirent. HEATIT is regiered Tradmark by zhukeshi(We didn't authize other sellers in Amazon.com).
  • Make a test when you received the product.  Put it into the freezer for 45 minutes.  And then plug in and you will see the red light on the thermostat control. Two year limited warranty- If you are not completely satisfied with HEATIT ET-21, please don't hesitate to contact us in any time, we'll try our best to solve your issues.
  • Can be use for other applications: 120 VAC electric heaters, gas heater, Engine heaters, pipe heat tape, roof heating cable and so on
  • Easy installation: just plug this device into electrical outlet. Maximum 15 amps. CSA approved. Only for dry location.
  • Energize below 38℉(3℃) and to turn off automatically at approximately 50℉(10℃). Automatically turns power on and off according to ambient temperature. Save energy and save money
  • Thermostat control outlet with the smart indicator light: The indicator light turns on when it's below 38 and it has energized the outlet.
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable.
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available; Suitable for most roof and gutter configurations.
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts.
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included.
  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact us in any time.
  • Idea for Indoor and outdoor applications: pipe heating cable attachment, duct insulation, general repair, cold and hot air ducts, HVAC, aluminum sealing, copper pipe fixing etc
  • Flame retardant, UV resistant, Chemically resistant. Perform well in thermally conductive. Improving the heating and cooling efficiency
  • HEATIT aluminum foil tape can stick well to most surfaces by its high quality acrylic pressure sensitive adhesive. A clean, dry and free of oil or grease surface is necessary before applying HEATIT aluminum foil tape
  • 2.0 inches wide x 30 feet (10 yards) length. 2.4 mil foil thick and 2.9 mil backing paper thick
  • HEATIT is registered Trademark by zhukeshi (We didn't authorize other sellers in Amazon.com). HEATIT aluminum foil tape provide a tough, strong bond at low and high temperatures from -22 F to 248 F
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty - If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we'll try our best to solve your issue.
  • Designed to maintain water temperature in the supply piping system, reducing or eliminating the delay in obtaining hot water at each fixture. You don’t need to run showers or sinks for long periods of time to draw new hot water into the unit, which is a significant waste of water. Simply wrap the self regulating heating cable around your hot water lines within the house to provide you with instant hot water. It is an energy efficient and economical alternative to common re-circulation systems.
  • Roof deicing application: HEATIT JHSF1 was designed to prevent the ice dam formation not to melt the ice dams which were already formed. Please turn on the cable at the beginning of snowing. Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
  • Smart plug with indication light to show you whether the cable is working or not. Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material. ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug.
  • HEATIT is registered Trademark by zhukeshi(We didn't authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.

More Info

1